Shopping Cart

Concealed Door Problems and Fixes: A Practical Troubleshooting Guide

A well-fitted concealed door is one of the neatest things you can put in a home. With no architrave and a leaf that sits flush with the wall, it all but disappears. The flip side is that a concealed door shows every small fault. A door that’s a millimetre out, a gap that’s wider at the top than the bottom or a hairline crack beside the frame is much easier to spot on a flat, painted wall than around a traditional door.

The good news is that most concealed door problems have simple causes, and many can be fixed with an Allen key and a bit of patience. This guide covers the most common issues, what usually causes them and when it’s time to call your installer.

Before you start: how a concealed door adjusts

Most concealed doors hang on concealed hinges that can be adjusted in three directions:

  • Height (vertical). Raises or lowers the door to even out the gaps at the top and bottom.
  • Side (horizontal). Moves the door towards or away from the hinge side to even out the gaps on the left and right.
  • Depth (compression). Moves the face of the door forwards or backwards so it sits flush with the frame and wall.

The adjustment range is small. Simonswerk’s Tectus TE 240 3D hinge, for example, adjusts by up to ±3mm sideways, ±3mm in height and ±1.5mm in depth. That’s plenty for fine-tuning, but it can’t make up for a frame that has been fitted badly out of plumb.

Italian door maker FIP Porte gives sensible advice for adjusting its concealed hinges, and it applies to most systems:

  1. Take the weight off the door. Open it to 90 degrees and slide a wedge underneath. FIP suggests raising the door at least 6mm off the floor so you’re not fighting its weight.
  2. Work from the top hinge down.
  3. Set every hinge to the same adjustment. If one hinge is moved more than the others, the door can twist.

Always check your own door’s fitting instructions first, as the screw positions and key sizes vary between brands. For more on hinge types, see our concealed door hinges guide.

Problem 1: the door rubs at the top or bottom

What you’ll notice: the door catches the head of the frame or scrapes the floor, and the gap above the door looks uneven.

Likely causes:

  • The door has dropped slightly on its hinges as it has settled in.
  • The hinges were never quite set to the same height.
  • A new floor finish, such as thicker carpet, rug or tiles, has raised the floor level.

How to fix it: use the vertical adjustment on each hinge to raise or lower the door, keeping all hinges at the same setting. If the floor level has changed significantly, adjustment may not be enough, and the door may need to be trimmed. Many concealed door leaves can’t be trimmed freely, so check with the manufacturer before you cut anything. Our guide to how to measure for a concealed door explains why the finished floor level matters so much at the planning stage.

Problem 2: the gaps on each side are uneven

What you’ll notice: the shadow gap is wider on the hinge side than the lock side, or the other way round, and the door might catch on the latch side.

How to fix it: use the side adjustment on each hinge. FIP’s guidance stresses setting all the hinges to the same distance, otherwise the door twists. Close the door after each small change and check the gap with your eye or a feeler gauge.

If the gap is wider at the top of one side and narrower at the bottom, the door is hanging out of square. Adjust the top and bottom hinges first, then bring the middle hinge into line.

Problem 3: the door sits proud of the wall, or sits back

What you’ll notice: the closed door isn’t perfectly flush. You can see a shadow along one edge, or the door sticks out slightly from the wall.

Likely causes:

  • The depth adjustment needs setting.
  • The magnetic strike isn’t holding the door tight against its stop.
  • The door leaf has bowed slightly.
  • The frame itself was set slightly back from or proud of the finished wall line.

How to fix it: start with the depth adjustment on the hinges, setting them all equally. If the hinge side sits flush but the latch side doesn’t, look at the strike plate (see Problem 4).

A bowed leaf is different. FIP fits a door straightener on some models and non-standard heights, and recommends using it only if the panel has genuinely warped, turning it a little at a time and stopping if a light adjustment doesn’t work. If your door doesn’t have one, speak to the supplier rather than trying to force it.

If the frame is out of line with the wall, no amount of hinge adjustment will fully hide it. That’s an installation issue, so talk to whoever fitted it. Our guide to concealed door frame details explains how the frame should relate to the wall finish.

Problem 4: the door won’t latch, or rattles when closed

What you’ll notice: the door bounces back instead of closing, closes but moves when you push it, or you have to slam it to make it catch.

Likely causes: many concealed doors use a magnetic latch. The bolt only pops out when it lines up with the magnet in the strike plate. If the door has moved even slightly, the two no longer line up.

How to fix it: first make sure the door is hanging correctly, using the hinge adjustments above. Then look at the strike. FIP’s advice is that if the door closes but there is still play, the fix is usually the strike plate rather than the hinges: loosen its screws, adjust the strike and tighten the screws again. It says you can take up as much as 2mm of play this way on its doors.

Our guide to magnetic latches for concealed doors explains how these latches work and what to check.

Problem 5: the door sticks after decorating

What you’ll notice: the door was fine until it was painted or papered, and now it binds or won’t close flush.

Likely cause: paint build-up on the edges of the leaf or inside the frame. The gap around a concealed door is very small, so even a couple of thick coats can be enough to make it stick. Paint in the hinges or latch can also stop them working.

How to fix it: let the paint harden fully, then lightly sand back the build-up on the edges and recheck the hinge adjustment. Never paper across the gap between the leaf and the frame. Our guide to how to paint a concealed door covers preparation, masking and keeping the gaps clear.

Problem 6: cracks in the plaster around the frame

What you’ll notice: fine cracks running along the line where the frame meets the wall, often near the hinges or the latch.

This is one of the most common complaints with concealed doors. Concealed door manufacturer Push & Pull explains that cracking happens when the frame and the wall move at different rates, either because the wall moves over time or because the frame moves, for example when the door is slammed.

Likely causes:

  • The frame wasn’t fixed often enough. Push & Pull says its own concealed frames should be screwed to the wall every 200mm, with fixings doubled up in the corners, though you should always follow your own manufacturer’s instructions.
  • The joint between frame and wall wasn’t reinforced with the tape or mesh the manufacturer specifies.
  • The door is being slammed, or is badly adjusted and knocking against the frame.
  • In a new building, the structure is still drying out and settling.

How to fix it: don’t just fill the crack and repaint. Check first that the frame is solid and the door closes gently and evenly. If the frame moves when you push on it, it needs more fixings, and that’s a job for your installer. Once the frame is stable, cut out the crack, reinforce it as the manufacturer recommends, then fill and redecorate. A soft-close or a well-adjusted door will help stop it coming back. Our guide to how to install a concealed door covers the correct plaster junction.

Problem 7: the door swings open or closed on its own

What you’ll notice: the door won’t stay where you leave it.

Likely cause: the frame isn’t plumb. A door hung on a frame that leans will always try to swing towards the low side. Hinge adjustment can’t correct this, because it moves the leaf, not the frame.

How to fix it: check the hinge-side jamb with a long spirit level. If it’s out of plumb, the frame needs re-fixing, which often means opening up the wall. If you need a door that closes itself, fit a proper closer rather than relying on a leaning frame. Our concealed door closers guide explains the options.

When to call a professional

Many adjustments are well within the reach of a confident DIYer. Call your installer or supplier if:

  • the frame moves when you push on it
  • the door has dropped more than the hinges can correct
  • cracks keep coming back after repair
  • the door is a fire door, as adjustments, gaps and any changes to the leaf must stay within its certification
  • the door is very heavy, as removing and rehanging a large leaf is a two-person job

For fire-rated concealed doors, see our guide to FD30 concealed doors and how to check a fire door.

Frequently asked questions

Why is my concealed door not flush with the wall?

Usually the hinge depth adjustment needs setting, or the magnetic strike isn’t pulling the door fully closed. If the frame itself sits proud of or behind the wall line, it’s an installation issue that hinge adjustment can’t fully fix.

How do I adjust concealed door hinges?

Take the weight off the door with a wedge, then use the height, side and depth screws on each hinge, working from the top down and keeping every hinge at the same setting. Follow your manufacturer’s instructions for screw positions and key sizes.

Why does plaster crack around a concealed door?

Cracks form when the frame and wall move at different rates. Common causes are too few frame fixings, a joint that wasn’t reinforced as specified, and doors being slammed.

Why won’t my concealed door latch?

The door has probably moved slightly, so the latch no longer lines up with the magnetic strike. Adjust the hinges first, then the strike plate.

Can I fix a sticking concealed door myself?

Often, yes. Most rubbing, uneven gaps and latching problems can be fixed with hinge and strike adjustments. Frame movement, fire doors and very heavy doors are best left to a professional.

Get the right concealed door from the start

Most concealed door problems trace back to the frame, the plaster junction or the finish, so a well-made system and careful installation save a lot of trouble later. Browse our concealed doors and concealed door accessories, or contact our team for advice on hinges, latches and frames for your project.

Leave a Reply

Your email address will not be published. Required fields are marked *


Powered by Startup Fast