Concealed doors look their best when nothing gives them away: no architrave, no visible hinges, just a fine line around the door. That’s easy enough on a painted wall. On a tiled wall, in a bathroom, en suite, kitchen or boot room, it takes a bit more planning.
Tiles add thickness, they meet the frame differently from plaster, and the grout lines can either hide the door or draw attention to it. This guide covers how to plan a concealed door in a tiled wall, from ordering the frame to the final joint, and whether it’s a good idea to tile the door itself.
Why tiles change the plan
A concealed door frame is fixed into the wall and then disappears under the wall finish. Our Frameless Hidden Door, for example, has an aluminium frame with an edge profile designed to grip the plaster, so you get an architrave-free finish. The door sits in the same plane as the finished wall on its flush side.
On a painted wall, “finished wall” means board or plaster plus a skim and paint. On a tiled wall, it also includes tile adhesive and the tile itself. That extra depth has three knock-on effects:
- Frame depth. The frame must suit the full finished wall thickness, including tiles on one or both faces.
- The flush face. If the tiles are on the flush side, the door face has to line up with the face of the tiles, not the plaster behind them.
- The junction. Tiles meet the frame edge at a hard line, and that junction needs a different approach from a plaster joint.
Step 1: work out the finished wall thickness
Before you order, add up every layer on each side of the wall:
- Stud or block width
- Plasterboard, backer board or plaster
- Tile adhesive
- Tile thickness
Specialist guidance on flush doors in tiled walls puts the extra thickness of adhesive plus tile at around 11–15mm per face for typical ceramic tiles, but use the figures for your own tiles and adhesive bed. If you haven’t chosen the tiles yet, plan for the thickest option you’re considering.
This matters because concealed hinges only have a small amount of depth adjustment. They’re designed to fine-tune the door so it sits perfectly flush, not to make up for a frame ordered for the wrong wall. If the frame is sized for the plastered wall and tiles go on afterwards, the door can end up sitting back from the tile face, so it looks recessed instead of hidden.
Our guide on how to measure for a concealed door walks through measuring the opening and wall build-up, and concealed door frame details covers push and pull options and the sequence of works.
Which side is flush?
A concealed hinged door is only truly flush on one face of the wall. Decide early which side that should be:
- Flush on the tiled side if the tiled room is the one you want the door to disappear in, such as a bathroom with a full-height tiled wall.
- Flush on the painted side if the door is mainly meant to vanish from a hallway or bedroom, with a simple reveal on the tiled side.
If you’re planning a hidden door into a bathroom, our guide to a hidden en suite door also covers privacy locks, ventilation and moisture.
Step 2: get the wall ready for tiles
The wall around a concealed frame needs to be strong enough for the tiles and stable enough that the door’s movement doesn’t crack them.
Choose a board that can take the weight
Tile weight limits depend on the surface. As our guide to tiling a pocket door wall explains, industry guidance from Instarmac and Topps Tiles gives a maximum of 32kg/m² for unskimmed gypsum plasterboard, including adhesive and grout, and 20kg/m² for a skimmed plaster surface. Heavier tiles need a backer board rated for the load. Don’t skim walls you plan to tile.
Don’t bond tiles straight to the frame
Tile adhesive is designed for boards, plaster and masonry, not smooth metal. The frame’s flange should be covered as the frame manufacturer specifies, with the tiles fixed to the wall surface rather than directly onto the aluminium. A door that is opened and closed every day puts repeated movement into that area, and tiles bonded to the frame can work loose.
Always follow the frame maker’s instructions for how the wall finish meets the frame. The details differ between systems.
Fix the frame first
Concealed frames go in at first fix, before plastering, boarding and tiling. The frame should be fixed solidly, plumb and square, because any twist will show up as an uneven gap that tiles make even more obvious. Our guide on how to install a concealed door covers the full sequence for stud and masonry walls.
Step 3: set out the tiles around the door
This is the step that makes the biggest visual difference. On a painted wall, the only line is the gap around the door. On a tiled wall, that gap sits among dozens of grout lines, so they need to work together.
- Line the top of the door up with a horizontal joint. Set out the tiles from the top edge of the door, so cut tiles end up at the floor or ceiling rather than over the door.
- Line the sides up with vertical joints where you can. If the door width isn’t a neat multiple of tile plus joint, make the cuts the same on both sides.
- Avoid thin slivers next to the frame. Narrow cut pieces beside the door are hard to cut cleanly and more likely to chip or come loose.
- Keep grout joints close in width to the door gap. When the grout joints and the door gap are a similar width, the door reads as part of the pattern.
- Think about large-format tiles. Fewer joints across the door width can make the set-out simpler.
- Watch where the tiling stops. If tiles stop part-way up the wall, think about where that line falls in relation to the door head, and whether running the tiles to the ceiling around the door would look neater.
Step 4: finish the joint at the frame
Grout is rigid, and the junction between tile and frame can move slightly as the door is used. For that reason, specialist guidance recommends leaving a narrow joint between the tile edge and the frame, filled with a flexible sealant rather than grout. A neutral-cure sanitary silicone is often suggested, because acetic (vinegar-smelling) silicones can mark some metals and natural stone.
Choose a colour that matches the grout, and keep the line the same width all the way round. An even line is what makes a concealed door look deliberate.
Should you tile the door itself?
It’s tempting to tile the door leaf so the wall looks completely continuous. In most homes, we’d advise against it on a standard concealed door, for a few reasons.
Weight
Tiles and adhesive are heavy. As an example, if your chosen tile and adhesive came to around 24kg/m², an 800 x 2100mm door (about 1.68m²) would carry roughly 40kg extra on one face. That’s on top of the weight of the door itself.
Concealed hinges have load limits. The Atlantic AGB Eclipse 3.2 heavy-duty self-closing concealed hinge we stock, for instance, is designed for doors up to 60kg. Add up the door, tiles, adhesive and any handle before choosing hinges, and check with the door and hinge makers. Our concealed door hinges guide explains the options.
Movement and clearance
Every time the door opens and closes, tiles on the leaf are moving, and the edge tiles pass close to the frame. Tiles can chip at the edges or debond from a surface that flexes. Tiles also add thickness to the door face, which can affect clearance as the door swings.
Better alternatives
- Paint the door to match. Most concealed doors are supplied primed for painting. Our Bespoke Concealed Door Set has a primed leaf, ready for painting or papering. A paint colour matched to the tile can look surprisingly seamless. See our guide on how to paint a concealed door.
- Tile up to a neat reveal. Have the door flush on the painted side and frame the opening with tiles on the tiled side.
- Use a purpose-made tiled access panel for small service openings, such as access to a cistern or valves. These are designed with a tile-ready face, set out to suit the tile size, and installed before the surrounding tiles.
If you really want a tiled door leaf, talk to the manufacturer before ordering, so the door, frame and hinges are specified for that load from the start.
Moisture in bathrooms and kitchens
Concealed doors in bathrooms need to cope with humidity. Use good extraction, seal all faces and edges of the door, and keep the door away from direct water. If your extractor relies on air coming in under the door, plan the gap at the bottom of the door from the start. Our hidden en suite door guide explains ventilation undercuts.
FAQs
Can you put a concealed door in a tiled wall?
Yes. Order the frame for the full finished wall thickness, including tiles and adhesive, fix the frame before tiling, and plan the tile set-out around the door.
Can I tile over a concealed door?
It’s possible with a door and hinges designed for the load, but we don’t recommend tiling a standard concealed door. Tiles add a lot of weight and can chip or come loose with movement. Painting the door to match is usually the better option.
What goes between the tiles and the frame?
A narrow joint filled with a flexible sealant, such as a neutral-cure sanitary silicone, is usually recommended rather than grout, because it copes better with small movements.
Do tiles affect the frame size?
Yes. Tiles and adhesive add to the finished wall thickness on each tiled face. Give your supplier the full build-up so the frame and door line up with the finished surface.
Can a concealed door go into a shower area?
It’s best to keep concealed doors out of areas that get wet directly. Place them where they’ll only see normal bathroom humidity, with good ventilation.
Plan your tiled concealed door
Explore our concealed doors and concealed door accessories, or contact our team with your wall build-up and we’ll help you choose the right frame.
