Pocket doors are a favourite for bathrooms, en suites and kitchens, which means sooner or later someone wants to tile the wall the door slides into. It can be done, and done well, but a pocket wall isn’t quite the same as an ordinary stud wall. There’s a hollow cavity where the door lives, so the boards over it have less support, and anything that goes through them could scrape the door.
This guide explains how to prepare a pocket door wall for tiles, how to work out whether your tiles are too heavy, and how to avoid the cracked grout and loose tiles that give pocket walls a bad name.
Why a pocket wall needs extra care
In a normal stud wall, plasterboard is screwed to vertical studs every 400mm or 600mm. Over a pocket, the boards are fixed to the kit’s frame instead, and behind them is an open cavity for the door. That causes three things to think about:
- Flex. If the pocket frame and boards aren’t stiff enough, the wall can move slightly when pushed or when the door runs. Tiles and grout don’t like movement. On DIY and trade forums, installers regularly report builders refusing to tile a pocket wall that has noticeable give in the middle.
- Fixings. Screws or anything else fixed through the board can poke into the cavity and catch the door.
- Weight. Tiles, adhesive and grout all add load to boards that are only supported at the frame.
Get the wall right before tiling and none of these needs to be a problem.
Step 1: Start with a solid, well-installed kit
Tiling success starts at installation. The pocket kit has to be plumb, square and properly fixed to the surrounding studwork and floor. Eclisse, for example, advises installing its frames at finished floor level and making the studwork strong enough to support the weight of the door, with the studs plumb and in line. Our pocket door installation guide and our guide to fitting a pocket door in a stud wall cover the essentials.
Before boarding, slide the door in and out several times. It should run smoothly without rubbing. Fix any problem now, because once the wall is tiled you won’t be able to get into the frame easily.
Step 2: Choose the right board
Pocket kits are generally designed to take standard 12.5mm plasterboard on each side. That is fine for many tiled walls, but the board you choose should match the room and the tile.
Dry rooms with light tiles
In a kitchen splashback or a dry area of a bathroom, moisture-resistant plasterboard is a common choice. It must be fixed firmly and not skimmed if you plan to tile directly onto it (see the weight limits below).
Wet areas
Where the wall will get wet, such as inside a shower area or in a wet room, plasterboard alone isn’t a good base. Tile backer boards (cement or XPS-type boards) are designed for wet areas and can take more weight. Installers on tiling forums often describe fixing backer board or adding a backer layer over the pocket, then tanking and tiling.
That said, it’s best to avoid putting a pocket door inside a shower enclosure at all. Water and the timber parts of a door don’t mix, and constant splashing will shorten the life of the door. Our guide to pocket doors for bathrooms covers good positions and ventilation.
Check the wall thickness
Every millimetre of board and tile adds to the finished wall. If you add a backer layer or double-board, the finished wall gets thicker, and that affects how the door’s split jambs and trims fit. Check this against the kit specification before ordering. Our pocket door wall thickness guide explains how finished wall thickness is worked out.
Step 3: Check your tile weight
Every wall surface has a maximum tile weight, including adhesive and grout. Tile adhesive maker Instarmac and retailer Topps Tiles both publish guidance figures:
| Surface | Maximum weight (tile, adhesive and grout) |
|---|---|
| Gypsum plaster (including skimmed plasterboard) | 20kg/m² |
| Gypsum plasterboard, unskimmed | 32kg/m² |
| Tile backer boards (Instarmac guidance) | 40kg/m² |
Topps Tiles quotes higher limits for some specific backer boards, so always check the figure from the board maker you’re using.
Adhesive and grout usually add about 2–4kg per m² (Instarmac’s figure; Topps Tiles suggests allowing 3kg per m²). Large-format porcelain and natural stone can be heavy, so look up the weight per m² of your chosen tile and add the adhesive and grout. If the total is over the limit for your board, you need a stronger board.
Two practical points:
- Don’t skim plasterboard you plan to tile. A skim coat drops the limit to 20kg/m².
- Prime the board as the adhesive maker recommends.
Step 4: Fix the boards without reaching the door
This is where pocket walls catch people out. Screws that are too long, or fixed in the wrong place, can protrude into the cavity and scratch the door every time it slides.
- Use the screw type and length the kit maker specifies. Some kits give a maximum screw length for fixing boards to the pocket frame. Follow it exactly.
- Fix only into the frame’s fixing points, not into empty cavity.
- Check the door after boarding. Slide it fully in and out. If you hear or feel any scraping, find the culprit before tiling.
No fixings through the tiles later
Once tiled, don’t drill through the pocket section to fit towel rails, shelves, mirrors or cabinets. Even short fixings can hit the door. Plan heavier items for the solid part of the wall, away from the pocket. The same applies to sockets, switches and pipes: they can’t run through the pocket area, so plan them elsewhere.
Step 5: Tile and grout to allow for movement
Even a well-built pocket wall can move very slightly. To reduce the risk of cracks:
- Use a flexible tile adhesive and grout suitable for timber or board substrates.
- Leave a movement joint where tiles meet the door frame and in internal corners, and fill it with a flexible sealant rather than grout.
- Keep tiles clear of the opening. Make sure no tile edge, trim or bead stops the door sliding or catches its edge.
If the door has trims or jamb pieces that fit over the tiled face, check how they’re fixed before tiling. Some need to sit on the board rather than on the tile, which affects where you stop the tiling.
Planning a tiled pocket door project
A little planning saves a lot of trouble:
- Choose the door position, ideally away from showers and splash zones.
- Pick the tile and work out its weight per m².
- Choose the board based on the room and the weight.
- Confirm the finished wall thickness works with your kit.
- Plan where rails, mirrors and electrics will go.
- Install, board and test the door before tiling.
Browse our pocket door kits and pocket door handles and hardware to choose a system, and see our pocket door problems and fixes guide if a door starts to rub.
Frequently asked questions
Can you tile over a pocket door frame?
Yes. Once the kit is installed and boarded, you can tile the wall on either side, as long as the boards are suitable for the room and the tile weight, the fixings don’t reach the door and the wall is stiff enough not to flex.
What board should I use on a pocket door wall in a bathroom?
Moisture-resistant plasterboard is often used in dry areas of a bathroom. In wet areas, use a tile backer board designed for wet rooms, and avoid placing the pocket door inside a shower enclosure. Always check your board choice against the kit’s specification and finished wall thickness.
How heavy can tiles be on plasterboard?
Industry guidance from Instarmac and Topps Tiles gives a maximum of 32kg/m² for unskimmed gypsum plasterboard, including adhesive and grout, and 20kg/m² for skimmed plaster. Heavier tiles need a backer board rated for the load.
Why did my tiles crack on a pocket door wall?
The most common causes are flex in the wall, tiles that are too heavy for the board, rigid grout at the junction with the frame, or fixings that have moved the board. Check that the frame and studwork are solid and use flexible adhesive, grout and sealant at movement joints.
Can I hang a towel rail on a tiled pocket door wall?
Not over the pocket itself. Fixings through the pocket section can hit the door. Mount rails, shelves and mirrors on the solid part of the wall beside the pocket.
Get your pocket door ready for tiles
A tiled pocket wall can look just as clean as any other wall in the room. If you’d like advice on choosing a kit or checking the finished wall thickness for a tiled bathroom or kitchen, contact our team and we’ll help you plan it.
