Pocket doors are brilliant space savers, but because they slide rather than swing shut against a door stop, they don’t seal in quite the same way as a hinged door. If you’ve noticed a chilly breeze around a pocket door in winter, or a gap you can see light through, you’re not alone.
The good news is that most pocket door draughts can be reduced with simple, inexpensive changes. The trick is choosing seals that work with a sliding door, rather than against it. This guide explains where draughts come from, which products are suitable and what you shouldn’t seal.
Why pocket doors can feel draughty
A hinged door closes against a stop on the frame, so a foam or rubber seal can be squashed between the two. A pocket door doesn’t do that. It runs on a track at the top, slides past the frame and needs small clearances all round so it can move freely. Those clearances are where air can sneak through.
There’s also the pocket itself. The door slides into a cavity in the wall, and the slot where it enters is open to that cavity. If the wall connects with colder spaces, such as an unheated loft, a floor void or a stud wall linked to an external wall, air can move through the pocket and into the room.
Where the draughts come from
Before buying anything, find the leaks. On a cold or windy day, run the back of your hand slowly around the closed door, or hold a candle or incense stick nearby and watch for the flame or smoke flickering. Check these areas:
- The pocket opening. The gap between the door face and the split jambs where the door disappears into the wall.
- The leading edge. Where the door meets the frame on the closing side.
- The top. The gap above the door, around the track and the head of the frame.
- The bottom. The gap between the door and the floor.
Also look for draughts that have nothing to do with the door, such as gaps between the frame and the plaster, or where the skirting meets the wall.
Which seals work on a sliding door?
Historic England’s guidance on draught proofing explains that wiper seals are the only way of sealing the sides of sliding sash windows and sliding doors. Wiper seals, most commonly brush pile strips, brush lightly against the moving surface rather than being compressed.
Foam and rubber compression seals are a poor choice for the sliding faces of a pocket door. They drag on the door, wear quickly and can make it hard to open.
Brush seals at the pocket opening
The pocket opening is usually the most important area to treat. A slim brush strip fitted to the inside face of the split jamb, so the bristles lightly touch the face of the door, can close the gap without being seen. Fit one on each side of the door. Keep the contact light, as too much pressure adds friction and can mark the finish.
The leading edge
On the closing side, the door meets the frame. Depending on your frame, a slim brush strip or a seal in the jamb can help. Some people simply find that adjusting the door so it closes squarely into the frame makes a big difference. Our guide to pocket door problems and fixes explains how to adjust a door that sits unevenly.
The top of the door
Air can move over the head of the door and along the track. A brush strip fitted along the head, touching the top edge or face of the door, can help, but it must stay clear of the track and runners. Never fit anything that could catch the hangers or the soft-close mechanism. If your door has soft-close, our soft-close pocket doors guide explains how it works.
The bottom of the door
Pocket doors hang from the top track, so there’s always a gap underneath. A brush strip on the face of the door near the bottom edge, or a surface-mounted brush, can reduce draughts. Be careful with floor guides, which keep the door in line, and don’t add anything that will scuff the floor. Our pocket door flooring guide covers floor finishes and clearances.
Don’t seal the bottom completely
It’s tempting to block every gap, but internal doors play a part in ventilating your home. Approved Document F, the ventilation guidance for England, says internal doors should allow air to flow through the dwelling, with a minimum free area equivalent to a 10mm undercut in a 760mm wide door. That means leaving a gap of 10mm above the floor finish, or 20mm if the floor finish isn’t fitted yet, unless air can move another way, such as through an air transfer grille.
So aim to reduce draughts, not to make the door airtight. This matters even more in homes with mechanical ventilation, which relies on air moving between rooms.
Tackling draughts from inside the wall
If air is coming through the pocket itself, the cause is often in the wall rather than the door. Look for:
- gaps where the stud wall meets an external wall, floor or ceiling
- openings around pipes or cables that run into the wall
- a pocket wall that’s open to a loft or floor void at the top or bottom
Sealing these from the room side, for example with decorator’s caulk along the junction between the frame and plaster, can help. If you’re building a new pocket wall, it’s the best time to think about airtightness. Our guide to pocket door frames covers how the frame and wall fit together.
If you also want a quieter room, many of the same steps help. Our pocket door soundproofing guide goes into more detail.
Fire-rated pocket doors
If your pocket door is part of a fire-rated system, don’t add seals, strips or anything else that isn’t covered by the manufacturer’s instructions and test evidence. Changes can affect how the system performs in a fire. See FD30 pocket doors explained for more on how fire-rated pocket systems work.
Quick checklist
- Find the leaks with your hand or a candle on a cold day.
- Fit light brush seals at the pocket opening on both sides.
- Check the leading edge and adjust the door if it closes unevenly.
- Treat the head carefully, keeping clear of the track and runners.
- Reduce the bottom gap without blocking the ventilation the room needs.
- Seal gaps around the frame and wall where they’re causing draughts.
- Test that the door still slides smoothly all the way open and closed.
Frequently asked questions
Why is my pocket door so draughty?
Pocket doors slide past the frame instead of closing against a stop, so they need small gaps to move freely. Air can come through these gaps and through the wall cavity the door slides into.
What’s the best draught excluder for a pocket door?
Brush seals are usually the best option. Historic England notes that wiper seals, such as brush strips, are the way to seal sliding doors, because foam and rubber seals drag on a moving door.
Can I put a draught excluder at the bottom of a pocket door?
You can reduce the bottom gap, but don’t seal it completely. Approved Document F expects internal doors to allow air to move through the home, typically with a 10mm gap above the floor finish, unless another air path is provided.
Will draught proofing make my pocket door harder to open?
It shouldn’t if the seals only touch the door lightly. If the door starts to drag, the brush is pressing too hard or is in the wrong place, so move or swap it for a softer, longer pile.
Can I draught proof a fire-rated pocket door?
Only in line with the manufacturer’s instructions. Adding unapproved seals or strips can affect the fire performance of the system.
Planning a new pocket door?
If you’re planning a new installation, choosing a good-quality kit and fitting it carefully makes a big difference to how well the door closes. Browse our pocket door kits and pocket door hardware, or contact our team for advice.
