Shopping Cart

Pocket Doors and Flooring: Floor Levels, Gaps and Underfloor Heating

Most pocket door advice focuses on the wall: how thick it is, how long the pocket needs to be and what runs through it. The floor gets far less attention, yet it causes some of the most frustrating problems. A door that scrapes, a floor guide that won’t fit, or a new floor that stops the door sliding out of the pocket can all be traced back to flooring decisions made at the wrong time.

This guide explains how flooring and pocket doors interact, what “finished floor level” really means, and how to plan tiles, wood, carpet and underfloor heating around a pocket door.

Why the floor matters so much with a pocket door

A hinged door swings over the floor, so if the floor is a little higher than expected you can usually trim the bottom of the door. A pocket door is different. It hangs from a track at the top of the frame and slides into a steel or timber pocket built into the wall. The height of that track is fixed once the frame is in and the wall is boarded.

That means the gap between the track and the floor has to be right from the start. If the finished floor ends up higher than the frame was set for, the door may catch on the floor or fail to slide out of the pocket. Eclisse makes this point directly in its installation tips: install the frame at finished floor level, or the door might not slide out of the pocket. It adds that with a wooden door you might be able to trim the bottom, but you can’t do that with a glass door.

What “finished floor level” means

Finished floor level (FFL) is the height of the top surface of the floor once everything is down. It is not the height of the joists, the subfloor or the screed. It includes every layer you plan to add, such as:

  • screed or a levelling compound
  • underfloor heating boards, insulation or pipes
  • underlay
  • the final floor covering, whether that’s tiles, engineered wood, laminate, vinyl or carpet
  • any adhesive bed under tiles

Most pocket door kit instructions are written around FFL. The Eclisse Syntesis installation guide, for example, is drawn from finished floor level and notes that the final flooring must be installed. Kit makers generally want the frame positioned so the door clears the finished floor, not the bare subfloor.

How to work out your FFL before the floor is down

If the new floor isn’t laid yet, add up the thickness of every layer you plan to use. Ask your flooring fitter for real figures, because tile adhesive beds and levelling compounds vary. Mark the finished floor height on the studwork or wall at the doorway, and set the pocket door frame from that line.

The gap under a pocket door

Every pocket door needs a small clearance between the bottom of the door and the floor so it slides without rubbing. The exact gap depends on the kit, its hangers and the floor guide, so follow the figures in your kit instructions rather than a rule of thumb.

The hangers on most kits allow some height adjustment once the door is hung. That adjustment is there to fine-tune the door, level it and set an even gap. It isn’t designed to make up for a floor that’s much higher or lower than planned.

The floor guide and your floor

Most pocket door kits include a floor guide. It sits at the entrance to the pocket and runs in a groove cut into the bottom of the door. Its job is to keep the door centred and stop it swinging at the bottom. Eclisse calls the floor guide essential, because it reduces movement and keeps the door in line so it meets the door post correctly.

How the guide is fixed matters for your flooring:

  • Guides fixed to the floor. Some systems have a guide that is screwed down at the pocket entrance. That means drilling into the finished floor, which needs care with tiles, stone and anything with pipes or cables beneath it.
  • Guides fixed to the frame. Other systems fix the guide to the frame instead. Eclisse’s Syntesis data sheet says its floor guide is not screwed into the floor, and points out that avoiding holes is a big help on tricky floors such as tiles or where there is underfloor heating.

If you’re laying a stone or porcelain floor, or you have underfloor heating, check how the floor guide fixes before you choose a kit. Our pocket door frame guide explains the main parts of a kit in more detail.

Underfloor heating and pocket doors

Pocket doors and underfloor heating (UFH) work well together, as long as you plan the two at the same time.

Know where the pipes or cables run

If your floor guide has to be screwed down, a stray fixing into a heating pipe or electric mat is an expensive mistake. Ask your heating installer for a layout drawing, and keep a clear zone at the pocket entrance where any guide fixings will go. If you’re adding a pocket door to an existing UFH floor and don’t know the pipe layout, a frame-mounted floor guide removes the need to drill into it.

Include the UFH build-up in your FFL

UFH systems add height. Some sit within the screed, while overlay systems add boards or panels on top of the existing floor. Either way, those layers are part of your finished floor level, so include them when setting the frame height.

Choosing flooring around a pocket door

Different floor finishes bring different considerations.

Tiles and stone

Tiles are hard, unforgiving and often slightly uneven from tile to tile. Aim for a flat, level run across the doorway and into the pocket entrance, so the door gap stays consistent along its travel. Plan any floor guide fixing before tiling, or choose a system where the guide isn’t screwed down.

Engineered wood, laminate and vinyl

These floors are usually thinner and more consistent, which makes them easy to plan around. Floating floors need expansion gaps at the edges. At a pocket door threshold, agree with your fitter how the floor finishes at the doorway, and keep trims low so the door doesn’t catch on them.

Carpet

Carpet and underlay can be surprisingly thick, and pile height varies. Measure the actual products you’ll use rather than guessing. If one side of the doorway is carpet and the other is a hard floor, plan the transition so neither surface sits higher than the door can clear.

Fitting a pocket door before or after the floor

There are two common approaches.

  1. Floor first, then frame. This is the simplest route. The finished floor is down, so you can set the frame straight from it and measure exact clearances.
  2. Frame first, floor later. This often happens in renovations and new builds where walls go up before floors are finished. It works well, but only if you know the finished floor height in advance and set the frame from it. Protect the pocket entrance during the build so plaster, screed or adhesive doesn’t get into it.

In both cases, the door itself is usually hung once the messy work is done. Our pocket door installation guide walks through the full fitting sequence.

What to do if the floor is already too high

If a new floor has gone down and the door now scrapes or won’t come out of the pocket, try these steps in order:

  • Adjust the hangers. Small height differences can often be taken up at the hangers. See our pocket door problems and fixes for how to diagnose and adjust.
  • Trim the door. A timber door can sometimes be trimmed at the bottom, as long as the door maker allows it and you re-cut the floor guide groove if needed. Glass doors can’t be trimmed, and fire doors can only be trimmed within the limits set by their manufacturer.
  • Get advice. If the difference is large, speak to your installer. The fix may involve reworking the floor at the doorway or adjusting the frame.

Frequently asked questions

Should a pocket door frame be installed before or after flooring?

Either can work. The key is that the frame is set to the finished floor level. If the floor isn’t down yet, add up every layer of the planned floor and set the frame from that height.

Can you have a pocket door with underfloor heating?

Yes. Plan the two together, include the UFH build-up in your finished floor level, and avoid drilling into pipes or cables. Some kits have a floor guide that fixes to the frame rather than the floor, which avoids drilling altogether.

How big should the gap be under a pocket door?

It depends on the kit and floor guide, so follow your kit instructions. The hangers usually allow some fine adjustment to set an even gap once the door is hung.

What if my new floor stops the pocket door sliding?

Start by adjusting the hangers. If that isn’t enough, a timber door may be trimmable. Glass doors can’t be cut down, and fire doors only within their manufacturer’s limits, so speak to your installer if the difference is large.

Plan your pocket door with the floor in mind

Getting the floor level right at the start saves a lot of trouble later. Browse our pocket door kits to compare frames for different wall thicknesses, and add soft-close or locking hardware from our pocket door hardware range.

Find the right pocket door kit for your project today.

Leave a Reply

Your email address will not be published. Required fields are marked *


Powered by Startup Fast