In a lot of British homes, the hallway is where doors fight each other. The living room door hits the radiator, the cloakroom door clashes with the kitchen door, and the coats on the wall stop anything opening fully. A pocket door can solve much of that, because it slides into the wall instead of swinging into the space you need to walk through.
Hallways also come with rules and quirks that other rooms don’t. They’re usually part of the escape route, they carry switches, radiators and coat hooks, and they often have doors on every wall. This guide walks through where pocket doors work well in a hallway, where they don’t, and how to plan them properly.
Why pocket doors suit hallways
A standard hinged door needs a clear arc to open. In a hall that might be only 900mm to 1,000mm wide, that arc can block the route, hit another door or force you to step back to let it swing.
A pocket door removes the swing completely. When it’s open, it disappears into the wall, so:
- You get the full width of the hall back
- Doors on opposite or adjacent walls can no longer collide
- Coats, shoes and furniture can sit where a door used to swing
- Wide openings into living or dining rooms can stay open most of the day without a door sticking out
If you’re weighing up the two door types more generally, our guide to pocket doors vs hinged doors sets out the pros and cons side by side.
Which hallway doors work best as pocket doors
Pocket doors work best on doors that are opened often and left open, or where a swing genuinely causes problems. Good candidates include:
- Living room and dining room doors. These are often left open, and a sliding door lets the rooms flow into the hall when you want them to.
- Kitchen doors. A pocket door keeps cooking smells and noise out when closed, then vanishes when you’re carrying shopping or plates through.
- Cloakroom and WC doors. Small downstairs toilets often have doors that clash with the hall or the WC itself. Our guide to pocket doors for cloakrooms covers these in detail.
- Utility rooms and coat cupboards. Useful where a hinged door would block a narrow side passage.
They’re less suitable where a door must be a fire door and you don’t want to use a fire-rated sliding system, or where there’s no clear wall beside the opening for the door to slide into.
Fire safety: check this first
Hallways and landings are usually the escape route, so check the fire rules before you choose any door.
Under Approved Document B in England, ground-floor habitable rooms (other than kitchens) should open directly onto a hall leading to a final exit, or have an emergency escape window or door.
In a house with a storey more than 4.5m above ground, the guidance calls for a protected stairway. Doors opening onto it in a single-family house need a minimum of FD20 (E 20). This often applies after a loft conversion, and it can include doors from the hall into ground-floor rooms. Our guide to pocket doors for loft conversions explains how this usually plays out.
A standard pocket door kit is not fire rated, so it shouldn’t go on a doorway that needs to be a fire door. If you want a sliding door in that position, you’d need a fire-rated pocket system tested as a complete assembly, such as an FD30 system, fitted exactly as tested. Our guide to FD30 pocket doors explains how these work. Always confirm your plans with building control, and check local guidance if you’re in Wales, Scotland or Northern Ireland.
Make sure there’s wall space for the pocket
A pocket door needs a stretch of wall beside the opening that’s roughly as wide as the door itself, so the door has somewhere to go. In hallways this is often the sticking point, because walls are broken up by other doors, the stairs or the front door.
Before you commit, measure:
- The width of the doorway you want to change
- The clear, straight run of wall on the side you want the door to slide into
- Whether that run is interrupted by another opening, a corner or the staircase
If one side is blocked, check the other. If neither side has enough space, a double pocket door splitting the opening in two, or a telescopic system, may help on wider openings. Our pocket door sizes guide explains how door and frame sizes relate.
Wall thickness and construction
Most pocket door frames are built into a stud wall, and the finished wall thickness depends on the kit. Hallway walls are often a mix of stud partitions and masonry, so find out what you’ve got.
- Stud walls are usually the simplest. The section of wall where the pocket goes is rebuilt around the kit. See our guide to fitting a pocket door in a stud wall.
- Brick or block walls can still take a pocket door, but it’s a bigger job and may involve structural work or building out a new stud section. Our guide to a pocket door in a brick wall covers the options.
If the wall is load-bearing, get a structural engineer involved before you open it up. For build-ups and finished thicknesses, see our pocket door wall thickness guide.
Switches, sockets and radiators
This is where hallways catch people out. The pocket section of the wall has to be clear, because the door slides right through it.
- Light switches. Hall switches often sit right beside the door. If that’s on the pocket side, the switch needs to move to the other side of the opening or to another wall.
- Sockets and cables. No sockets or cables should run through the pocket. Plan rerouting before you start, and use a qualified electrician.
- Radiators. You can’t hang a radiator on the pocket section, because the fixings would go into the door’s path. Radiators are often in hallways for good reason, so check where yours can go instead.
- Coat hooks, shelves and pictures. Long screws into the pocket section can scratch or jam the door. Keep heavy fixings off that stretch of wall, or use fixings short enough to stay within the board, following the kit maker’s advice.
Handles, locks and soft close
Pocket doors need flush handles, because anything that sticks out would stop the door sliding fully into the wall. For a hallway door you’ll usually want a flush pull on both faces and an edge pull on the leading edge so you can draw the door out of the pocket. Our guide on how to choose pocket door handles explains the options.
If the door leads to a WC or cloakroom, add a privacy lock. Our pocket door locks guide covers hook locks and privacy sets.
Soft-close is worth considering on busy hallway doors, especially in family homes. It slows the door as it closes or opens fully, which helps with noise and stops it slamming into the frame. See our soft-close pocket doors guide for how it works.
Glazed or solid?
Hallways are often dark, with light coming only from the front door or a landing window. A glazed pocket door into a living room or kitchen can borrow light from that room and make the hall feel brighter. Our glass pocket doors guide covers glazing styles and practical points.
Solid doors are better for privacy and for keeping sound in. Pocket doors generally don’t seal as tightly as hinged doors, so if noise between the hall and a room matters, read our guide to pocket door soundproofing.
Planning checklist
- Check whether any hallway doors need to be fire doors, and agree it with building control.
- Measure the clear wall run beside each opening.
- Find out whether the wall is stud or masonry, and whether it’s load-bearing.
- Plan where switches, sockets and radiators will move to.
- Choose the kit, door, handles and any lock or soft-close together.
- Book the work in before plastering and decorating.
Frequently asked questions
Are pocket doors a good idea for hallways?
Often, yes. They’re especially useful in narrow halls where hinged doors clash or block the route. They need clear wall space beside the opening and aren’t suitable where a fire door is required unless you use a fire-rated sliding system.
Can a hallway pocket door be a fire door?
A standard pocket door kit isn’t fire rated. Where a fire door is needed, you’d need a fire-rated pocket system that has been tested as a complete assembly, such as an FD30 system, and building control should confirm it meets the requirement.
Can I put a light switch next to a pocket door?
Yes, but not on the wall section the door slides into. Switches and sockets should go on the other side of the opening or on another wall.
Can I hang a radiator on a pocket door wall?
Not on the pocket section. Radiator fixings would go into the door’s path, so the radiator needs to go elsewhere on that wall or on another wall.
Can I fit a pocket door in an existing hallway?
Usually, if there’s enough wall beside the opening. Expect to open up the wall, fit the frame, and then make good and redecorate, so it’s best combined with other hallway work.
Plan your hallway pocket door
If your hallway doors keep clashing, a pocket door is one of the simplest ways to get the space back. Browse our pocket door kits, choose the hardware to go with it, or get in touch if you’d like help choosing the right system for your hall.
