Shopping Cart

Pocket Doors for Offices and Commercial Spaces: A Practical Guide

In a busy office, swinging doors cause more trouble than people expect. They clash in narrow corridors, eat into small meeting rooms and get propped open because nobody wants to fight with them. A pocket door slides into the wall instead, so the floor space in front of the opening stays usable.

But commercial buildings come with rules that don’t apply at home: fire safety law, accessibility guidance and workplace regulations. This guide covers where pocket doors work well in offices, clinics, salons and shops, where they shouldn’t be used, and what to check before you order. If you’re fitting one at home, our guide to pocket doors for home offices is the better starting point.

Where pocket doors work well in commercial spaces

Pocket doors are at their best on internal doors that are opened often but don’t need to be fire-rated or acoustically sealed. Good examples include:

  • Small offices and one-to-one rooms, where a swinging door would hit the desk or the chair behind it.
  • Corridors and break-out areas, where open doors would block the route.
  • Kitchenettes, tea points and print rooms, which are often left open during the day and closed at night.
  • Stores and cleaners’ cupboards, where shelving can go right up to the opening.
  • Treatment rooms and salon back rooms, where floor space is valuable and staff carry things through with full hands.
  • WCs, where a pocket door can make a small room easier to use, with a suitable privacy lock.

A double pocket door can also link two meeting rooms or open a room onto a break-out space for events.

Where pocket doors shouldn’t go

Emergency exits

The Regulatory Reform (Fire Safety) Order 2005, which applies to most non-domestic premises in England and Wales, says sliding or revolving doors must not be used for exits specifically intended as emergency exits, and that emergency doors must open in the direction of escape. So a pocket door is not an option for a fire exit.

Escape routes and fire doors

Many office doors sit on escape routes or form part of a fire-resisting wall, such as the doors to a protected corridor or stair. Whether a sliding door is acceptable there depends on the building’s fire strategy, so talk to your fire risk assessor or building control before you plan one.

Fire-rated pocket door systems do exist, but they’re specialist, tested assemblies with their own certification. Our guide to FD30 pocket doors explains how they work and their limitations.

Accessibility: clear widths and handles

Effective clear width

Approved Document M Volume 2, which covers buildings other than dwellings in England, gives minimum effective clear widths for doors. For a straight-on approach, it suggests 800mm in new buildings and 750mm in existing buildings. Where a door is reached at right angles from a corridor at least 1,200mm wide, the figures rise to 825mm for new buildings and 775mm for existing ones.

With a pocket door, the clear width isn’t the same as the door width. Part of the leaf usually stays visible so you can grip it, and the handle and frame take up space too. Our pocket door sizes guide explains the difference between the door size and the passage size. If you’re tight on width, a larger leaf, a telescopic pocket door or a double kit may help.

Handles people can actually use

Small recessed finger pulls look tidy but can be hard to use for people with limited grip. In a commercial space, consider:

  • A larger flush pull that’s easy to hook fingers into.
  • An edge pull, so the door can be drawn out of the pocket.
  • A pocket door lock with a large thumb-turn for WCs and treatment rooms.
  • A soft-close mechanism, which helps the door close gently and avoids slamming.

Our guides to pocket door handles and pocket door locks cover the options.

Safety rules for sliding doors at work

Two sets of rules are worth knowing.

The Workplace (Health, Safety and Welfare) Regulations 1992 say any sliding door in a workplace must have a device to prevent it coming off its track during use.

Approved Document K, which covers protection from falling, collision and impact, says sliding doors should have a stop or other effective means to stop them coming off the end of the track, and a retaining rail to stop them falling if the suspension system fails or the rollers leave the track.

A well-designed pocket door kit has end stops and a guided track, but check the kit’s instructions and confirm with your installer how it meets these points. Don’t remove stops or anti-derailment parts to get a bit more opening width.

Glazed pocket doors

Glazed doors are popular for meeting rooms because they keep the space bright. Approved Document K says glass doors and glazed screens in non-domestic buildings should carry manifestation (visible markings) at two heights: between 850mm and 1,000mm and between 1,400mm and 1,600mm above the floor. The markings should be clearly visible, for example lines, patterns or a company logo. The glass itself must also be suitable safety glass. Our glass pocket doors guide explains what to check.

Durability in a busy building

A pocket door in a shared office may be opened hundreds of times a day, so build in some extra robustness:

  • Pick a kit rated well above the door’s weight. Weight ratings vary between kits, so check the figure against your actual door, including any glass and handles.
  • Use a solid, well-made door. A hollow or lightweight leaf can flex and rattle with heavy use.
  • Protect the leading edge. Busy doors get knocked by trolleys and chairs, so a hardwearing finish helps.
  • Think about maintenance. Many kits let you adjust or replace the runners without opening the wall, but not all do. Check before you buy.
  • Keep the pocket clear. Nothing should be fixed into the pocket wall where screws could reach the door, including shelving, signs or display rails.

Our pocket door hardware range includes handles, locks and soft-close parts.

Walls and partitions

Many offices use metal stud partitions rather than timber studwork. Before you order, check that the pocket door kit suits the partition system and its thickness, and agree with the partition installer how the kit’s frame will be fixed.

Also plan the services. Data cabling, light switches and sockets can’t go in the section of wall that houses the pocket, so they need to move to the other side of the opening. Our pocket door wall thickness guide explains how the finished wall is built up.

Sound and privacy

Pocket doors can’t seal as tightly as a hinged door with seals on all four sides, so sound travels more easily around them. They’re fine for a general office or break-out area, but think carefully about rooms where conversations must stay private, such as HR meetings, consulting rooms or interview rooms.

There are ways to improve performance, such as brush seals and a solid door. Our guide to pocket door soundproofing covers what works. If speech privacy is critical, a hinged acoustic door may be the better choice for that room.

A quick planning checklist

  1. Confirm the door isn’t an emergency exit and check with your fire risk assessor whether it sits on an escape route or in a fire-resisting wall.
  2. Work out the effective clear width you need, then size the door and kit to suit.
  3. Choose handles and locks that everyone can use.
  4. Check the kit has end stops and anti-derailment features.
  5. Plan manifestation and safety glass for glazed doors.
  6. Check the kit suits your partition system and move services out of the pocket.
  7. Decide whether the room needs better sound privacy than a pocket door can offer.

Frequently asked questions

Can pocket doors be used in offices?

Yes. They work well for small offices, stores, kitchenettes, WCs and rooms off busy corridors. They aren’t suitable for emergency exits, and doors on escape routes or in fire-resisting walls need checking with your fire risk assessor or building control.

Can a pocket door be a fire exit?

No. The Regulatory Reform (Fire Safety) Order 2005 says sliding doors must not be used for exits specifically intended as emergency exits.

How wide should a pocket door be for wheelchair access in an office?

Approved Document M Volume 2 suggests a minimum effective clear width of 800mm for a straight-on approach in new buildings, rising to 825mm where the door is approached at right angles from a 1,200mm corridor. Remember that a pocket door’s clear width is less than the door leaf width.

Do glass pocket doors in offices need markings?

Usually, yes. Approved Document K says glass doors in non-domestic buildings should have manifestation between 850mm and 1,000mm and between 1,400mm and 1,600mm above the floor.

Are pocket doors good for meeting rooms?

They’re good for general meeting rooms where space is tight, but they don’t seal as well as hinged doors. For confidential rooms, add seals and a solid door, or consider a hinged acoustic door.

Plan your commercial pocket doors

Browse our pocket door kits, including single and double systems, or contact us with your opening sizes and partition details and we’ll help you choose.

Leave a Reply

Your email address will not be published. Required fields are marked *


Powered by Startup Fast