Timber frame homes are common across the UK, especially in Scotland and on many newer estates. Because their internal walls are usually studwork, they can seem like the perfect place for a pocket door. In many cases they are. A pocket kit is designed to sit inside a stud wall, so you don’t have the cutting and rebuilding that a brick or block wall needs.
But a timber frame house isn’t just a set of stud walls. Some internal walls carry loads from floors and the roof, others stiffen the building against the wind, and walls between neighbouring homes do a fire and sound job. This guide explains how to tell which walls you can work with, what to watch for in new homes, and how to plan a pocket door properly.
How a timber frame house works
In a timber frame house, the structure is a frame of timber panels rather than masonry. The outside may still be brick, render or cladding, but that outer layer is usually not what holds the house up.
The Structural Timber Association’s homeowner guide, Living in a modern timber frame home, explains that internal wall panels have plasterboard on both sides and are usually hollow, although insulation may be added to reduce noise. It also says that sheathing board is sometimes added for extra stiffness, and that this may indicate the wall is load-bearing.
For a pocket door, the internal walls fall into three broad groups:
- Non-load-bearing partitions. These just divide rooms. They’re the best candidates for a pocket door.
- Load-bearing walls. These support floor joists or roof loads from above.
- Walls that add stability. Some walls resist wind and keep the building stiff, even if they don’t carry much vertical load.
Step 1: Find out which walls are structural
The STA guide says the easiest way to understand your home’s structure is to look at the working drawings submitted to building control when the house was built. If you don’t have them, your local authority building control department may hold copies, or a structural engineer can advise.
If you don’t have drawings, the STA guide gives some clues:
- Floor joist direction. You can often work out which way the joists run from the pattern of screws or nails in the floor deck. Walls running across the joists, roughly where they’d need support, are more likely to be load-bearing. The guide notes joists rarely span more than about 4m, though they don’t always all run the same way.
- Doubled or tripled studs. A post made of two or three studs fixed together suggests the wall is carrying a concentrated load.
- Plywood or OSB on one side. This may show the wall is designed to take horizontal forces from wind, even if it isn’t carrying vertical loads.
- Walls at right angles to the front or rear wall. On wider homes, of more than about 7m, the STA says designers sometimes use these walls to stabilise the building against wind pressure. They must be kept.
The STA guide is clear on the bottom line: be absolutely sure a wall is non-load-bearing before you remove part of it, and if you’re in any doubt, ask a structural engineer. Work on load-bearing walls must be notified to building control, and the STA strongly advises against DIYers making structural changes to them.
Step 2: Leave separating walls and external walls alone
Two kinds of wall should never take a pocket door.
Separating (party) walls
In semi-detached and terraced timber frame homes, the wall between you and your neighbour is a separating wall, often built as two separate timber leaves. It’s there to stop fire and sound passing between homes. Cutting a pocket into it would undermine that, so it’s off limits.
External walls
External timber frame walls contain the structure, insulation, a vapour control layer and the outer cladding system. A hollow pocket would cut through all of that, so pocket doors belong in internal walls only.
Step 3: Choose the right wall for the pocket
Once you’ve identified a suitable non-load-bearing partition, check it can take a pocket:
- Length. The door slides into the wall, so you need roughly twice the door width of straight wall, with no junctions, corners or doorways in the way.
- Thickness. The pocket kit and its boarding set the finished wall thickness. Our pocket door wall thickness guide explains what to allow.
- Services. Stud walls often carry cables and sometimes pipes. These have to be rerouted out of the pocket area by a competent person.
- What’s above. Even in a non-load-bearing partition, the opening needs a proper head and secure fixing to the structure.
Usually the cleanest approach is to take the section of partition out and rebuild it with the pocket kit, rather than trying to cut the kit into the existing wall. Our guide to fitting a pocket door in a stud wall walks through this, and our pocket door installation guide covers the full process.
If the wall you want turns out to be structural, you still have options. An engineer may design a solution with a new lintel and supports, or you could add a new partition alongside. Both need professional design and building control involvement.
New-build timber frame homes: allow for movement
Timber shrinks as it dries. NHBC Standards explain that as a timber frame dries out it shrinks and its overall height reduces, and that this differential movement increases with the number of storeys. NHBC also says timber should have a maximum moisture content of 20% at the time of dry lining, to minimise shrinkage.
What does that mean for a pocket door?
- In a brand new home, some settling is normal in the first period of occupation. Small cracks at plasterboard joints and around door frames are common as the frame dries. If you’re planning a pocket door soon after moving in, ask your builder or warranty provider for advice, and avoid tight tolerances.
- Check the door again after installation. Most pocket door kits have adjustable hangers. If the door starts to rub or drift as the house settles, a small height adjustment usually sorts it. Our guide to pocket door problems and fixes explains how.
- Don’t build the partition tight to the floor above in a way that could make it carry load. NHBC guidance on non-load-bearing partitions warns against over-wedging them against joists or trusses.
If your home is still under a new-home warranty, check before altering walls. Changes could affect what the warranty covers, so read your policy or ask the provider first.
Planning a pocket door in a timber frame extension or new build
If you’re building, a timber frame project is a great time to add pocket doors, because you can design them in from the start:
- Tell your designer and frame supplier early, so pocket positions appear on the drawings.
- Keep pockets in non-load-bearing partitions wherever possible.
- Choose your kit before the partition design is fixed, so wall thickness and opening sizes match.
- Agree with building control which doors, if any, need to be fire doors. A standard pocket kit isn’t fire rated, so see our guide to FD30 pocket doors if a fire door is needed.
Our guide to pocket doors for extensions covers timing and sequencing in more detail.
Finishing touches
Timber frame homes can be a little livelier acoustically than masonry ones, because internal walls are lighter. If you want a quieter room, use a solid door, add insulation to the rest of the partition and look at brush seals. Our guide to pocket door soundproofing explains what makes the biggest difference.
For the door itself, any door that suits your kit’s size and weight limits will work. See our guide to choosing a door for a pocket door kit. Add flush pulls, a privacy lock where needed and, if you like, soft-close dampers from our pocket door hardware range.
FAQs
Can you put a pocket door in a timber frame house?
Yes, in most cases, as long as it goes into a suitable non-load-bearing internal wall. Avoid load-bearing walls, walls that stabilise the building, separating walls and external walls unless an engineer has designed a solution.
How can I tell if a timber frame wall is load-bearing?
Check the original working drawings first. Clues include the direction of the floor joists, doubled or tripled studs, and plywood or OSB sheathing. If you’re in any doubt, ask a structural engineer.
Is it easier to fit a pocket door in timber frame than brick?
Usually, because internal timber frame partitions are already studwork. With brick or block, you often need to rebuild part of the wall in studwork or build a false wall. See our guide to a pocket door in a brick wall.
Will shrinkage affect my pocket door?
In newer timber frame homes, the frame can shrink as it dries, which may cause small movements. Most pocket kits have adjustable hangers, so a minor rub can usually be fixed by adjusting the door height.
Do I need building control approval?
If you’re altering a load-bearing wall, yes, the work must be notified to building control. A pocket door in a non-load-bearing partition may not need approval, but check with your building control body if you’re unsure.
Find the right kit for your home
Browse our pocket door kits to compare systems for different wall thicknesses and door sizes. If you’d like a hand working out which kit suits your timber frame walls, contact our team.
