Once the pocket frame is in and the wall is boarded, the opening still needs finishing. That’s where jambs, architrave and skirting come in, and it’s also where a lot of pocket door problems start. A nail in the wrong place can scratch the door every time it slides, and the wrong trim can make the door awkward to use.
This guide explains how a pocket door opening is usually finished, how to choose and fix architrave, how to run skirting across the pocket wall safely, and what changes if you choose a frameless pocket door with no architrave at all.
How a pocket door opening is finished
Most standard pocket door kits are designed to be finished like an ordinary doorway, with timber linings (often called a jamb kit) and architrave over the top. The parts do different jobs:
- The jamb or lining kit finishes the inside of the opening, covers the edges of the pocket and gives the door something to close against.
- The architrave is the decorative moulding around the opening on each face of the wall. It covers the joint between the lining and the plaster.
- The skirting runs along the bottom of the wall, including the section where the door is hidden.
Eclisse, for example, says its classic pocket door systems need finishing with architrave, with a jamb kit fitted underneath. Its jamb kit is attached to the pocket framework, covers the edges of the door when it’s closed so you can’t see into the pocket, and includes brushes and small rubber bumpers. The exception is its flush, no-architrave range, which doesn’t use a jamb kit at all.
Our guide to pocket door frames explains the difference between standard frames with architrave and frameless frames in more detail.
Step 1: choose the right jamb kit
The jamb kit has to match the finished wall thickness. That’s the stud plus the board on each side, plus any plaster skim. Eclisse offers its single jamb kit in five versions, for 95mm, 100mm, 115mm, 125mm and 140mm finished walls, and asks you to choose when you order the frame.
We stock a single timber lining (jamb) kit made for Rocket pocket kits. It’s white primed MDF, comes in 95mm, 100mm, 115mm and 125mm finished wall versions, works with 35mm or 44mm doors, and finishes the pocket entrance, the door post and the area above the opening. There are double door jamb kits too.
If you’re not sure of your wall thickness, our pocket door wall thickness guide shows the common builds.
Brushes and door thickness
The brushes at the pocket entrance help stop you seeing into the pocket and keep dust out. They need to suit the door thickness. Eclisse supplies two sets of brushes, 15mm and 10mm, to cope with both 35mm and 44mm doors. Check that your kit matches the door you’re using. Our guide to choosing a door for a pocket door kit covers thickness and weight.
Step 2: choose your architrave
Pocket door kit makers generally don’t supply architrave. Rocket’s installation guide says it doesn’t supply architraves because the choice is an individual one, and Eclisse says the same, so you can match the architrave to the rest of the house.
A few practical points when choosing:
- Match your other doors. The same profile and width as the other doorways keeps the pocket door from looking like an afterthought.
- Check it covers the joint. The architrave needs to cover the line where the lining meets the plaster, with a small margin.
- Think about the handle. Pocket doors use flush pulls and edge pulls rather than lever handles. Make sure the architrave doesn’t get in the way of your fingers when you reach for the pull at the pocket entrance. Our guide on how to choose pocket door handles explains the options.
- Slimmer can be better. A very deep, ornate architrave can make the pocket entrance feel cramped, especially on a narrow door.
Step 3: fix the architrave without damaging the door
This is the part that needs the most care. Behind the plaster on the pocket side of the opening is a hollow cavity where the door slides. Any nail or screw that goes through into that cavity can scratch the door, or stop it sliding.
- Fix to the lining, not into the pocket. Fix the architrave to the edge of the jamb kit, and to solid timber where there is some, rather than through the plasterboard over the pocket.
- Use adhesive and short pins. The Skirting Board Shop notes that architraves are often fitted using a combination of gap-filling adhesive and lost head nails. On a pocket door, keep pins short enough that they can’t reach the cavity.
- Avoid nail guns on long settings. A long nail fired at an angle is the classic way to end up with a pin sticking into the pocket.
- Test the door before filling. Slide the door in and out after fixing the architrave. If anything catches, it’s much easier to find and fix before the nail holes are filled and painted.
If the door has already started rubbing, our pocket door problems and fixes guide explains how to track down a protruding fixing.
Step 4: run the skirting across the pocket
Skirting usually needs to run across the wall where the door is hidden, on both sides. It’s the same problem as the architrave: there are no studs to nail into over the pocket, and any long fixing could go straight into the door’s path.
The safest approach is to fix skirting over the pocket section with adhesive only:
- Use a gap-filling adhesive. The Skirting Board Shop says skirting can be fixed to the wall using a gap-filling adhesive. That’s the best option over a pocket.
- Screw only where there’s solid fixing. Its guidance says that if screw fixing is needed, the skirting should be drilled and countersunk and fixed with a screw of appropriate length. On a pocket wall, keep screws to the studwork beyond the pocket.
- Keep it short of the opening. Stop the skirting at the architrave, as you would on any doorway, so it doesn’t interfere with the door or the brushes.
- Mark where the pocket is. Before decorating, note where the pocket starts and ends. It helps the next person who fits a shelf, a radiator or a picture hook.
Our guide on fitting a pocket door in a stud wall recommends keeping shelves and picture hooks off the pocket section altogether, for the same reason.
What about tiles or cladding?
If the pocket wall is being tiled, panelled or clad, the trims may need to sit on the board rather than on the tiles. Check this before tiling. Our guide to tiling a pocket door wall covers board choice and fixings.
Step 5: decorate the jambs and trims
Finish the jambs and architrave before the room is decorated:
- Primed MDF linings are ready for painting.
- Timber jambs can be painted, stained or varnished. Eclisse says its beech-veneered jambs are ready to paint, stain or lacquer, while the Ermetika Evokit raw wood jambs we sell are ready to be stained or varnished.
- Paint the door edges too, so the door is sealed on all faces. Our guide on how to paint a pocket door covers getting the door out of the frame and painting it evenly.
Keep paint off the brushes and the bumpers.
Prefer no architrave? Choose a frameless kit
If you’d rather not have architrave at all, you need a frameless pocket door system from the start. You can’t simply leave the architrave off a standard kit, because the lining edges and the joint with the plaster would be on show.
A frameless system uses a profile that’s plastered in flush with the wall, so the opening is a clean edge. The Ermetika Absolute Evokit frameless pocket door system we sell needs no trims, comes with its jambs as standard and allows a plaster reveal. Skirting then simply stops at the plastered edge of the opening, or you can plan a recessed skirting detail with your builder.
FAQs
Do pocket doors need architrave?
Standard pocket door kits are usually designed to be finished with a jamb kit and architrave. Frameless pocket door systems are plastered in flush and don’t need architrave.
Do pocket door kits come with architrave?
Usually not. Manufacturers such as Rocket and Eclisse don’t supply architrave, so you can match it to your other doors. Jamb kits are often ordered separately to suit your wall thickness.
How do you fix skirting over a pocket door?
Use a gap-filling adhesive over the pocket section, and only use screws or nails into solid studwork beyond the pocket. Long fixings over the pocket can scratch or block the door.
Can I nail architrave to a pocket door frame?
Fix it to the jamb kit and solid timber with adhesive and short pins. Don’t nail through the plasterboard into the pocket cavity, and test the door before filling the holes.
What size jamb kit do I need?
It depends on the finished wall thickness: stud, plasterboard on both sides and any skim. Common sizes include 95mm, 100mm, 115mm and 125mm.
Find the right kit and finishing parts
Browse our pocket door kits and pocket door hardware, or get in touch and we’ll help you match the kit, jambs and wall thickness.
