A garage conversion is one of the most popular ways to add a home office, playroom, gym, guest bedroom or utility space without building an extension. Garages are rarely generous, though. A typical single garage is long and narrow, so every bit of floor space counts, and a door that swings into the room can eat into the space you’ve just gained.
That’s why pocket doors are such a good fit. The door slides into a cavity inside the wall, so there’s no swing to plan around and no door blocking furniture. But a garage conversion has its own quirks: floors that sit lower than the house, masonry walls, and fire separation if part of the garage stays as a garage. This guide explains where pocket doors work well, what to check, and how to plan them in at the right stage.
Why pocket doors suit garage conversions
Most garage conversions turn one long space into one or two smaller rooms. That creates a few situations where a sliding door really earns its place:
- Splitting the space. Many people divide a garage into a front room (an office or bedroom) and a rear section for a utility room, shower room or storage. A pocket door in the new partition keeps both rooms usable.
- Adding a shower room or WC. A small shower room or cloakroom at the back of a garage bedroom is a common layout. A hinged door into a tiny bathroom can make it awkward to use. See our guide to pocket doors for bathrooms for what to consider in wet rooms.
- Storage and plant. Garages often keep the boiler, consumer unit or water tank. A pocket door to a cupboard keeps access easy without a door swinging into the room.
- Opening onto a hallway. If the converted room opens off a narrow hall, a pocket door avoids clashing with other doors or radiators.
If your new room will be a home office, our guide to pocket doors for home offices covers privacy, sound and layout in more detail.
Get the building regulations side right first
Before you think about door styles, it’s worth knowing that converting a garage into a habitable room is building work that normally needs building regulations approval. Several local authority building control teams list garage conversions among the projects that need an application, and inspections as the work progresses. Planning permission is a separate question, so check that with your council too.
Building control will look at the whole conversion, including foundations under the old garage door opening, insulation, damp proofing, ventilation, fire safety and escape. Doors come into it in a few places, so agree the door plan with your designer and building control body before you order anything.
Fire separation if you keep part of the garage
If you only convert part of the garage and keep the rest for a car or storage, the wall between the new room and the remaining garage needs adequate fire separation. Building control guidance commonly says a door in that kind of wall should be fire resisting and self-closing. For example, Ribble Valley Borough Council’s guidance says a door between a house and an integral garage must be FD30 with a self-closing device and a cold smoke seal.
A standard pocket door kit is not a fire door. If a sliding door is needed in a fire-separating wall, you would need a pocket system tested and certified as a complete fire-rated assembly, and you’d need building control to accept it, including how it closes. In many projects the simpler answer is a hinged fire door in that position and pocket doors elsewhere. Our guides to FD30 door requirements and FD30 pocket doors explain the options.
Escape routes and inner rooms
Fire safety guidance in Approved Document B also matters if the new room changes how people escape from the house:
- Inner rooms. An inner room is one you can only reach through another room. Approved Document B only accepts certain inner rooms, such as kitchens, utility rooms, bathrooms and WCs, or rooms with a suitable emergency escape window. If your garage bedroom is reached through a utility room, for example, building control will look closely at the layout.
- Houses with a storey above 4.5m. In taller houses, Approved Document B expects a protected stairway or an alternative approach, and doors onto it may need to be fire doors. If your converted room opens onto the hall that forms part of that route, its door may need to be fire resisting.
These are design decisions for your designer and building control, not something to assume. Once you know which doorways have to be fire doors, you can use pocket doors confidently everywhere else.
Floor levels: sort them before the pocket goes in
Garage floors usually sit lower than the floor in the house, and they often slope towards the garage door. Warwick District Council’s building control guidance notes that garage floors are generally raised as part of a conversion, either with insulation and a screed over a damp-proof membrane, or with treated timber joists and insulation over a membrane.
This matters for a pocket door because the kit is installed to suit the finished floor level. If the floor is raised after the pocket is built, the door won’t fit the opening properly. Our pocket door flooring guide explains how floor finishes affect the gap under the door.
A sensible order is:
- Agree the new floor build-up and finished floor level with your builder.
- Raise and finish the structural floor (screed or deck) to that level.
- Build the stud walls and install the pocket kits, set to the finished floor level.
- Board, plaster and decorate.
- Hang the door and fit the floor finish, checking clearances.
If you’re using a screed, allow it to dry as your builder or the screed supplier advises before laying timber or laminate floors.
Which walls can take a pocket door?
New stud partitions
This is where pocket doors are easiest. When you divide a garage, the new internal wall is usually a timber or metal stud partition. You can simply build the pocket kit into it. The wall needs to be thick enough for the kit and long enough to take the door when it’s open, so a pocket door needs roughly twice the door width of straight wall. See our pocket door wall thickness guide and pocket door sizes guide, and our guide to fitting a pocket door in a stud wall.
The wall between the house and the garage
In an integral garage, the wall between the garage and the house is often brick or block, and it may be load-bearing. You can’t simply cut a pocket into masonry. The usual options are to form the opening and build a new stud section, or to add a false stud wall alongside. Altering a load-bearing wall needs a structural design and building regulations approval. Our guide to fitting a pocket door in a brick or block wall explains the choices.
Remember the fire separation point above too. If this wall is staying as the separation between the house and a remaining garage, a standard pocket kit isn’t suitable.
External walls
Avoid putting a pocket in an external wall. Those walls need insulation and weather protection, and a hollow pocket would leave a weak spot. Keep pockets in internal walls.
Practical design tips
Plan the walls around the pocket
The section of wall that houses the pocket can’t take ordinary fixings, so think ahead:
- Sockets and switches. Keep them off the pocket section, or use a kit and layout that allows for them. Our pocket door installation guide covers this.
- Radiators and shelves. Don’t plan heavy items over the pocket. Put them on solid studwork beyond it.
- Tiles. If the pocket wall is in a shower room, read our guide to tiling a pocket door wall before choosing boards and tiles.
Think about sound
Garage conversions often become offices, bedrooms or gyms, and sound matters in all of them. A pocket door won’t seal as tightly as a well-fitted hinged door with seals, so if quiet is important, use a solid door, insulate the partition and look at brush or acoustic seals. Our guide to pocket door soundproofing explains what helps.
Choose the right door and hardware
A garage conversion is a chance to choose doors that match the rest of the house. Most pocket kits take a standard internal door, as long as it suits the kit’s size and weight limits. Our guide to choosing a door for a pocket door kit walks through this.
For a smoother, quieter feel, consider soft-close dampers, which we cover in our soft-close pocket doors guide. Flush pulls and edge pulls are best, because standard lever handles stop the door sliding fully into the pocket. For bathrooms and WCs, fit a privacy lock designed for sliding doors. You’ll find handles, locks and dampers in our pocket door hardware range.
Single, double or something else?
If you’re opening up a wide doorway, such as between a garage playroom and a kitchen, a double pocket door can give a much wider opening that still closes off when you need it. Our guide to single vs double pocket doors compares the two.
If the opening is an unusual size, as converted spaces often are, made-to-measure pocket doors can help you avoid awkward compromises.
A simple planning checklist
- Check planning and building regulations requirements for your conversion.
- Agree with your designer and building control which doors must be fire doors.
- Decide the finished floor level and raise the floor first.
- Plan where each pocket will go, allowing about twice the door width of clear wall.
- Keep sockets, switches, radiators and heavy fixings off the pocket sections.
- Choose the kit, door and hardware together, so sizes and weights match.
- Order early, so the kits are on site before the partitions are built.
FAQs
Do I need building regulations approval for a garage conversion?
Usually, yes. Converting a garage into a habitable room is normally building work that needs building regulations approval. Check with your local building control body or a registered building control approver before you start.
Can I fit a pocket door between my house and garage?
Only if fire separation is dealt with properly. A door between a house and a garage is commonly required to be a self-closing FD30 fire door, and a standard pocket kit doesn’t meet that. Agree the approach with building control first.
When should I install the pocket door kit?
After the floor has been raised to its finished level and before the walls are boarded. The kit is set to the finished floor level, so the floor needs to be sorted first.
How much wall space does a pocket door need?
Roughly twice the width of the door, because the door needs somewhere to slide into. The wall also needs to be thick enough for the kit you choose.
Will a pocket door keep noise out of a garage office?
It will help, but it won’t seal as well as a well-fitted hinged door with seals. A solid door, an insulated partition and good seals all make a difference.
Ready to plan your conversion?
Browse our pocket door kits to find the right system for your new room. If you’re not sure which kit suits your walls or opening, get in touch with our team and we’ll help you choose.
